Tag Archives: chinese laser

40W Chinese Laser: More upgrades

Made some upgrades over the long weekend:

Took out the stock work holder in preparation for the adjustable Z bed. It is hard to see in the first picture, but all but two of the posts were standing about 10% off of vertical. Even the allen screws securing the original work holder were at an extreme angle:

IMG_0939

IMG_0940

The LED strip lights got installed. If there is any upgrade that adds instant polish to your rig, its this one. The lights look amazing:

IMG_0950

IMG_0951

IMG_0953

Also removed all of the original cooling system and installed fresh tubing. Added reservoir, radiator, fan and anti-freeze:

IMG_0954

IMG_0957

IMG_0959

40W Chinese Laser: First cuts with open-source toolchain

Now, since I haven’t removed the stock work area, and because of the way the machine homes before the cut, I had to rest the test piece up higher than the normal work height. Outside the ideal laser focus width. Therefore the cut width is a bit thicker than if the material was a proper distance from the lens.

Still, I’m pretty happy with the performance – this is an example of a vector drawing:

IMG_0938

Digital source:

Screen Shot 2015-09-04 at 9.17.55 PM

40W Chinese Laser: Public Service Announcement: Clean your mirrors and lenses!

Don’t trust that your mirrors and lenses will be even remotely clean.

Remember when I mentioned I saw some soot on the lens carrier? Well, today I took it out for a closer inspection:

IMG_0933

And the mirror wasn’t in much better shape:

IMG_0934

I cleaned them up with some alcohol imbibed lens wipes:

IMG_0937

40W Chinese Laser: Brain Transplant!

IMG_0857

I’m removing the stock controller board. The proprietary software is terrible. It is getting replaced with the Open Source RapRep RAMPS G-Code controller. Thanks to the customized Marlin firmware by TurnkeyTyranny, this gives us several new advantages:

  • open source software chain (thanks again to TurnkeyTyranny and the Inkscape G-Code Export Extension)
  • programmatic control over the laser output power (ditching that terrible manual pot)
  • A slick new LCD control panel
  • I’m surprised I’ve not seen this elsewhere, but I plan to use a thermistor in my coolant tank to monitor the coolant temperature. Hopefully I can hack the firmware to stop firing the laser if the tank temperature rises beyond the set threshold.

    I ordered a new ribbon connector and made a new transfer cable to connect to the RAMPS pins. I was too impatient to design and order a wiring harness board, so I just soldered the cable right to the pins on the connector. I covered the contacts with some Liquid Electrical Tape.

    IMG_0928

    Below is a diagram of the wiring. Thankfully this was my exact power supply, so I didn’t have to get creative. Now, on the RAMPS, the servo pins are marked 2B 2A 1A 1B and the diagram has A- A+ B- B+. Here is the translation:

    A- -> 2B (ribbon cable pin 9)
    A+ -> 2A (ribbon cable pin 10)
    B- -> 1A (ribbon cable pin 11)
    B+ -> 1B (ribbon cable pin 12)

    It’s also not very clear on the diagram, but the XHOME goes on the first Signal pin on the endstop header and YHOME goes to the third signal pin. Even though it shows the 5v and GND going to the AUX-3/SPI header, you can use any 5V/GND connections on the other AUX or SERVOS header blocks.

    The Y stepper cable connects the following colors to pins:

    red -> 2B
    blue -> 2A
    white > 1A
    yellow -> 1B

    I’m borrowing this photo from TurnkeyTyranny’s git repo and putting this here so I can find it later:

    wiring_diagram

    This is not the greatest photo, but some of the wiring choices can been seen here:

    IMG_0927

    I made sure to test the steppers and homes before I even hooked up the laser fire and PWM controls to the RAMPS board. Once everything was moving as I expected, it was time to test the laser! Something about this screen preparing to push the button had me feeling like a mad evil genius set to take over the world: “FIRE ZEE LAZOOR!”

    IMG_0930

    As you can see by the burn, the initial tests were a success:

    IMG_0932

    Now its time to mount the board and get the wiring cleaned up to make room for more upgrades!

40W Chinese Laser: First cuts!

Today I finally wrangled a Windows XP machine back into shape so that I could run the stock software that works with the stock controller board.

I did the test cuts on 1/8″ thick hardboard.

We immediately see the value in having an air assist cutting nozzle. Without one, the exhaust fan pulls the smoke and heat up and across the work.
IMG_0889

No problem – a couple hits with the sandpaper and its clean! Not bad for a machine out of the box with zero calibration!
IMG_0890

The RAMPS arrives Monday. That’s when the teardown and upgrade will begin. Honestly, I can’t wait, because the stock software provided is terrible! Perhaps I’ll experiment with different power settings in the meantime.

40W Chinese Laser: Improvements

This is currently just a list of the upgrades I intend to make on my new machine. I’ll add links as I complete each item:

Add LED interior lighting
Remove controller and replace to RAMPS CNC controller
Replace controller panel with RAMPS LCD and switches for cooling, lighting, etc
Change chassis bolts to proper length
Add Air Assist head and pump
Upgrade Water Cooling
Enlarge build area
Upgrade Exhaust Assembly
Add fan to interior of power supply

LINK: Click here for a link to my post that contains a shopping list of parts required for the various upgrades.

40W Chinese Laser: Upgrade Parts List and RAMPS conversion

All of the following links are for items on Amazon. With a few exceptions, all qualify for Prime free shipping.

RAMPS Parts:
RAMPS + Arduino + Stepper Drivers
RAMPS LED Display
E-Stop Switch

Power Supply Cooling:
60mm 24v Fan for P/S

Exhaust Upgrade:
Exhaust Fan
Fan Hose
Hose Clamps

Laser Cooling Upgrades:
Water Reservoir
Heat Exchanger
Heat Exchanger Fan
Cooling Hose

Air Assist Upgrades:
Air Pump – hold off on this: waiting for pump to arrive to see if it can produce sufficient air flow.
Manifold – hold off on this: waiting for pump to arrive to see if I can reroute three of the four outlets internally.
Air Assist Hose
Drag Chain for Air Assist Hose

Interior Lighting:
LED Strip
LED Power Supply I chose the 2A model, only slightly more expensive, and the terminals have more substance.

40W Chinese Laser: Unboxing

I ordered mine from the San Leandro, CA facility. It shipped on a Monday via FedEx. It arrived two days later, on Wednesday.

I was surprised at the size of the unit – I had imagined it to be about 75% of its actual size. The wooden box was a bit beat up, half the screws were missing and the lid was otherwise held on by packing tape.
IMG_0842

The second (cardboard) box inside was in very good shape.
IMG_0843

The entire machine was tightly surrounded by 1″ thick, cheap styrofoam. I’m pretty sure they just broke up the pieces by hand to make them fit in the shipping container, as there were small bits of foam all over the place. Get your shopvac handy to pick up all the snow!
IMG_0845

Unpacked. Back of the unit. Covered in broken styrofoam. The cooling hoses are very soft and were crushed and deformed by the tight stryofoam packing. They function ok, but some parts seem to have melded themselves with the foam somehow. Notice the lines are filled with water, so they did actually do some testing before they shipped it out.
IMG_0846

Front. Covered in packing cellophane wrap. For some reason the lid is jammed open a bit. Perhaps because of the items packed inside.
IMG_0847

Removed the wrapping film and we now see the accessories inside. This bag contained a tube of silicone paste (I’m assuming for lubricating the rails), a roll of cheap double sided tape (the manual mentions using this over the mirrors to check alignment), a DVD-R (containing instructional PDF, CorelDraw and CorelLaser software) and a USB key – I have read elsewhere that this is a dongle that allows use of the Corel Laser software.
IMG_0848

USB A to B cable, exhaust fan and aquarium pump (for laser cooling).
IMG_0849

Took me a moment to notice the exhaust fan hose (blue, behind the lens head). Hose expands to about 6 feet in length. Also hidden under the platform is the 110v power cable.
IMG_0850

Closeup of the cooling hose. Note they are still very wet inside. Some sections are more opaque than others. I’m assuming their test water also had some sort of antifreeze in it, as my pump was also covered in some milky white residue around the outlet connection.
IMG_0851

A bunch of styrofoam “snow” trapped in the power connector.
IMG_0852

Some of the frame bolts are MUCH longer than they need to be. I will be replacing these with bolts of the appropriate length. Some are so long that they are offsetting the ability for the machine to sit flat on the four rubber corner stands.
IMG_0853

The interior of much of the machine was VERY dusty with brown dirt. No telling how long the chassis parts might have sat in an open warehouse or even outdoors prior to assembly.
IMG_0854

Laser tube. While a but dusty (probably from the dust falling from the top of the bay door that was pictured above), it looks to be in very good condition.
IMG_0855

More styrofoam snow in the back of the power/control compartment. All the wiring is wrapped and appears to be tidy. Not the horror show rats-nest or unshielded wiring that I’ve seen arrive on other Chinese laser builds.
IMG_0858

Back of control panel.
IMG_0859

Power supply.
IMG_0860

They obviously test-fired the laser as there was a good amount of soot on the bottom of the lens carrier. I have yet to remove the lens. I plan to take it out for inspection and cleaning – mirrors too. I’ll add to this post with those details later.
IMG_0861

They must slap these things together very quickly. The shield acrylic (in addition to being very scratched up by the stored accessories mounting) is crooked as all get out.
IMG_0862

Here’s a shot to show the size of the thing on my workbench. Again, much larger than I anticipated it would be. Pretty crazy for such a small work area of 12″x8″. I’ll certainly be making modifications to make for a larger build area.
IMG_0863

I did some checks to make sure the mirrors were aligned (I forgot to take pictures of that process). Turns out everything was in line and I successfully fired my first hole in a piece of thin cardboard!

New owners note: The way the switches work are not very clear in how they are labeled

Power: This is obvious. Nothing will happen unless this in On and glowing.
Laser Switch: This is an up/down locking toggle pushbutton. This essentially arms the laser.
Laser Power needle indicator: This will only indicate the read amperage of the laser *while it is firing*. Turning this, even when the Laser Switch is On, will not result in the needle moving. I suggest no more than a quarter turn clockwise when first test firing the laser.
Laser Test: if the “Laser Switch” is in the on/down locked position, this momentary switch will fire the laser. A quick pulse is usually sufficient.
IMG_0865

That’s it for the unboxing.

LINK: Click here for a WIP/TODO post that lists the improvements I’d like to make.

LINK: Click here for a shopping list of all required upgrade parts available on Amazon.com.